Installing A Bath tub
Installing A Bath tub
Blog Article
They are making a few good points regarding How to Install a Bathtub overall in this content down the page.
Installing a tub isn't precisely rocket science, however it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a new one is likewise a reasonably tough project. If the old bathtub is readily easily accessible, the project can relocate speedily; if you have to open up a wall to get rid of the old tub and also position the brand-new bathtub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to vacate the old bathtub and embeded in the brand-new one. Make sure you have qualified yourself for the work and fit attempting it. Instead of working with a contractor to take over a halfway-completed task, it is better to think about using one prior to you start. Chances are you may need a specialist plumber to make tube links.
This article will assist you mount a brand-new bathtub in your restroom if you have currently bought a new tub and don't require to transform the setup of your previous water supply pipelines.
Your tools and material checklist must consist of the following:
Getting ready for the Installment
First of all, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps device to stop pressure on the bath tub.
Fit the adaptable tap ports to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the supply of water. After doing so, switch on the taps to drain any water remaining in the system. The process of getting rid of the existing faucets can be quite problematic due to the restricted accessibility that is typically the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will come from the pipelines. When the supply pipelines have actually been removed, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old securing compound.
Prior to carrying on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Making use of both wooden boards under its feet, put the bathtub in the called for position. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
The following objective is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the tub until the level reviews level.
To mount taps, fit all-time low of the furthest versatile faucet connector to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the water supply as well as check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the bath tub and likewise examine the overflow outlet as well as the regular outlet for leaks.
Ultimately, fix the bathroom paneling as described in the maker's instruction manual. Tiling and also securing around the bathtub must wait till the bathtub has actually been made use of at least once as this will certainly resolve it into its final setting.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washing machines remain in place between the tap as well as the sink. Protect the faucet in position with the supplier provided backnut. As soon as the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind should be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture a rigid seal, causing the water to pass through the wall surface in between the bath and the tiling, resulting in complications with dampness and feasible leakages to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your components as well as fittings. They are offered in tubes as well as cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to always load the tub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealer can fracture relatively early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
We had been made aware of that editorial about How to Install a Bathtub from an associate on a different blog. Are you aware of anybody else who is intrigued by the subject? Feel free to promote it. Thanks for going through it.
Free Quote
Report this page